How to Replace a Kia Sportage Replacement Key
For many Kia models, the key contains a keyless entry system built-in. This key typically resembles the remote control and is able to be replaced by a new one purchased from a Kia dealer or locksmith.
Key fobs might stop working due to a variety of reasons, such as the battery being dead, worn-out buttons signals, signal interference or water damage. Here are some helpful tips on how to get your Kia Sportage replacement key back to working.
How do you replace a smartkey or remote key?
The battery in your Kia's intelligent key will eventually need to be replaced, whether it's a remote key that starts with a push button or a standard metal key that does not contain a transponder. This is especially relevant if your vehicle shows a message that states the remote or smart keys have low battery power.
This is a relatively easy process. To replace the battery on the keyfob, remove your mechanical key from the slit at the back of the fob. Then, pry the cover open. A small screw will be inside the key fob to keep the battery in place. Utilizing a small screwdriver loosen the screw and remove the old battery. Install the new battery and then close the cut on the key fob.
Test the key fob by pressing the lock and unlock buttons. If the doors lock and unlock as expected, then you're in good shape! You can now take advantage of your Kia's hands-free lock/unlock feature whenever your fingers feel cold or you need to make errands in Brandon.
Not all keys may require to be programmed (transponder chips or smart keys). This requires a programing machine that is available only to the locksmith for cars or dealer. Other keys (non-transponder metal keys) do not require programming. If your key requires to be reprogrammed, you must be aware of the key code that is stamped on the key code tag and then record it in a safe location.
How do I replace a battery
If your Kia key fob is not responding when you press the lock or unlock button on the fob, it is a clear indication that the battery needs to be replaced. A weak battery can cause other issues such as the check engine light coming on or the engine not cranking. Fortunately replacing the key fob battery is a simple DIY task that requires only the most basic tools.
Make sure that you shut off your vehicle and shut all doors prior to beginning. Find the small, metal or plastic piece that is on the bottom of your key fob, and gently jiggle it until the metal key pops out. Then, you can put the key into the driver's door handle to unlock your car.
To replace the key fob's battery, take off the cover on the rear and use a plastic pry bar tool to remove the latch holding the black negative battery cable. Take the old battery out, and then position the new battery so that its "+" side is facing you, and the "-" negative side is facing the fob's electrical contacts. Avoid using too much force when pushing the new CR2032 into position to avoid damaging or bending the metal contacts.
After installing the new battery then turn the key fob on and off in the ignition until the door locks cycle. You can then test the Kia's key fob to ensure it's working properly.
How do I replace a smart key
Depending on the model of your Kia Sportage, you may have an ordinary key fob or a smart key. The smart key is equipped with an embedded mechanical key blade however, the standard key fob does not. Both kinds of key fobs come with batteries inside that will eventually have to be replaced. This is a simple procedure that takes less than two minutes.
Before you start it is important to make sure that you are on a level surface with enough lighting and that the Kia is off. Keep in mind that the fob has small parts that can fall when you're not careful.
The first step is to find the small release button on the backside of the fob. It's either a circular button or rectangular slot. Once you press this mechanical key blade, it will be released and you will be able to open the key fob.
Once 2013 kia soul key fob replacement have the key fob opened, you can simply take off the old battery and replace it. The new battery is one called CR-2032 and can be bought through the internet or at a local auto parts shop. When you are done you should be able to lock or unlock your vehicle using your key fob even if the engine isn't running!
How do you replace a mechanical key
The Kia key fob is a great convenience that lets us lock and unlock our vehicle with the touch of the button. But like any device it will encounter issues from time to time. There are solutions to solve these issues and keep your key fobs in good working order for an extended period of time.
One of the most common issues is a low or dead battery. This could cause the fob to stop working altogether or work intermittently. If this is the case then try replacing the battery with a fresh new one.
If this does not resolve the issue, use a standard flathead screwdriver to wedge the plastic casing of the fob open. Be careful not damage any internal components or scratch the plastic. After the battery has been removed, replace it with a brand new battery.
Close and open the door with the mechanical key. (Every kia fob comes with a spare mechanical key which will fit into the slot). Test the key fob to confirm it's functioning properly. Contact a dealer, or a locksmith to solve the issue when the fob still is not working. Make sure they make you an emergency key that can work across all trunk and door cylinders to avoid lockouts in the future.